72-LED "Super Bright" ENGINE Accent Light Kit...
"Super Bright" ENGINE Accent Light Kit...
De Beers sent me this photo... Real nice... Outstanding...
I would like to thank Ryan for the following Review, he installed the Regular 180-LED Accent Kit so imagine what the "Super Bright" will do...
"These lights are the best I have installed, easy, bright and the best thing is almost no special modification were needed. I have installed three (3) sets of accent lights with pods from a different manufacturer and I thought they looked good but compared to Joe's they can't compare. The strips are awsome and mount with almost no clearance. TELLING ALL MY FRIENDS." Ryan...
This is the Ultimate in Single Color LED Lighting for Motorcycles
SingleColor WaterProof & ShockProof
The 72-LED Engine Kit
2 Strips 36-SingleColor LED Accent Light Flexible Strip... WaterProof & ShockProof...
Two WaterProof & ShockProof Flexible Strips Two (2) Flexible Strip that are 20 inches long and has 72-SingleColor LEDs spaced less than 1/2 inch apart... Both ends of the Flexible Strip has connectors and supplied with 3 feet of Tube Covered Heat Resistant Extension Wire. You can cut this strip one time and use both ends of the strip...
Very Important: If you cut the strip put some silicone sealant (included) on the cut end after you secure the strip in place... Or a small piece of electrical tape wrapped around the cut end works just as well...
Yes, It's "Super Bright" & WaterProof & ShockProof...
Recomended Placement: Cut each strip into one of 27-LEDs and the other of 9-LEDs
1) 27-LED Strip under the LEFT side of the gas tank...
2) 27-LED Strip under the RIGHT side of the gas tank...
3) 9-LED Strip behind the BREATHER between the two cylinder heads...
4) 9-LED Strip behind the HORN between the two cylinder heads...
Note: The reverse of the Flexible strip has 3-M adhesive that will stick to any cleaned surface...
Connect it all together
Now Connect the Engine Kit, Road Coverage Kit, the Front & Rear Wheel Kit and the Two (2) Extra Strips to the On-Off Switch and Fuse Holder.
Splice the RED Positive (+) wires of the Engine Kit together with the use of the E-Z Connect Terminals. Connect to one wire of the On-Off Switch, then connect the other wire of the On-Off Switch to one wire of the Fuse Holder, and then connect the other wire of the Fuse Holder to the Positive (+) Pole of the Battery.
Splice the BLACK Negative (-) wires of the Engine Kit together with the use of the E-Z Connect Terminal. Then connect this to the Negative (-) Pole of the Battery.
Then activate the On-Off Switch to the "ON" Position and you have the most beautiful Motorcycle Accent Lights you have ever seen...
This Kit Is Designed To Work On Any Bike Made...
You can expand this Kit by just adding more Strips and connecting to the E-Z Connect Terminals.
8 Ultra Bright LED Colors Currently Available:
Blue (12,000 MCD)
Green (15,000MCD)
Red (10,000 MCD)
Yellow (7,000 MCD)
Purple (5,000 MCD)
White (20,000 MCD)
Orange (8,000MCD)
Pink (8,000MCD)
1)Please be advised that color PURPLE is still a UV color and is almost half as bright as any other color...
2) The 5050 SMD Blub has three sections and normally this is used for RGB or MultiColor but in this case we are illuminating all three sections in the same color. Which is why this product is so bright it is thre blubs in one...The MCD figures above is the measurement of just one section of the blub... This 5050 SMD illuminated in such a way makes this product at least two times brighter if not greater than the normal 3528 SMD...
Yes an Engine Kit of 72-LEDs to accent the engine area of your bike.
This "Super Bright" Flexible Strip Kit is the brightest kit on the market bar none... It's like a blast of light shining on your chrome... Like an eruption of light... An explosion of light... A detonation of light... I am sure you will get a bang out of it...
Check this kit when you first get... Do not install it... Just connect a Strip to your battery and if it is not the brightest kit you ever saw return it for a full refund and I will even pay your return postage...
72-LED "Super Bright" SingleColor WaterProof ShockProof ENGINE Accent Light Kit
Remember: A lifetime guarantee. I don't give you any mumbo-jumbo just a very simple lifetime quarantee: should a light ever burn out or stop working for any reason, return it and I'll replace it. No ifs, ands or buts about it. You don't like my Kit just return it for a full refund of your purchase price including shipping cost. No questions asked... I know you will like this kit so when you receive it Do not install it... Just connect a Strip to your battery and if it is not the brightest kit you ever saw return it for a full refund and I will even pay your return postage...
Here's What you Get...
1 72-LED "Super Bright" Flexible Strips Engine Kit of Ultra High Brightness LEDs
1 On-Off Switch
1 Fuse Holder w/ Two 3amp Fuses
1oz Tube of Silicone Sealant
10 4" Plastic Wire Ties
5 Butt Splices
10 Cradle Mounts
2 E-Z Connect Wire Terminals
4 Feet of Double 20 gauge Wire
New & Improved Supply Kit
1oz Tube of Silicone Sealant is included to seal any cut ends of Flexible Strips...
Detailed “Installation Instructions” are included but most important I am available via phone or e-mail if you need additional help... I don't go away after the sell...
Are the LED Bulbs Waterproof?
Just look at the picture below with the BLUE Strip in a vase of water...
Yes. If installed according to the instructions there is absolutely no way that water will affect the performance.
How long will these lights last??
Almost forever... well, 100,000+ hours of light time (that's over 11 years) and for a light bulb that's almost forever. Also, these lights generate no heat and draw about 3 mill amperes each.
"Quality LED Accent Light Products at a Fair Price"
Have a Blessed Day... Joe-Florida...
It's Included!!!
3-M 94 Primer
PREPPED: "To prepare or prime"
Yes, 3-M 94 Primer is the best product on the market to prep the area where you are going to place the Flexible Strip. You will clean (degreaser) the location, you will rub the location with an included Alcohol Pad and one dry you will brush on the 3-M 94 Primer. Let dry for 3 to 5 minutes then secure the Flexible Strip to the location. Please understand that once you place the strip using these products and methods you will have to work at it to remove the strip. Be careful not to get 3-M 94 Primer on a noticiable finished painted or chromed surface. Best product to secure Flexible Strips in place. Use at your own risk!!!
This product was added to our catalog on Sunday 31 July, 2011.
