180-LED Accent Light Kit by JoeFlorida
Engine Kit, Front-Rear Wheels Kit & Road Coverage Kit...
De Beers sent me this photo... Real nice... Outstanding...
I would like to thank Ryan for the following Review...
"These lights are the best I have installed, easy, bright and the best thing is almost no special modification were needed. I have installed three (3) sets of accent lights with pods from a different manufacturer and I thought they looked good but compared to Joe's they can't compare. The strips are awsome and mount with almost no clearance. TELLING ALL MY FRIENDS." Ryan...
This one has a manual On/OFF Switch...
SingleColor WaterProof & ShockProof
The Engine Kit
2 Strips 45-SingleColor LED Accent Light Flexible Strip... WaterProof & ShockProof...
Two WaterProof & ShockProof Flexible Strips Two (2) Flexible Strip that are 20 inches long and has 45-SingleColor LEDs spaced less than 1/2 inch apart... Both ends of the Flexible Strip has 3 feet of Tube Covered Heat Resistant Wire which means you can cut this strip one time and use both ends of the strip...
If you cut the strip put some silicone sealant on the cut end after you secure the strip in place... Or a small piece of electrical tape wrapped around the cut end works just as well...
Yes, It's WaterProof & ShockProof...
Recomended Placement: Cut each strip into one of 36-LEDs and the other of 9-LEDs
1) 36-LED Strip under the LEFT side of the gas tank...
2) 36-LED Strip under the RIGHT side of the gas tank...
3) 9-LED Strip behind the BREATHER between the two cylinder heads...
4) 9-LED Strip behind the HORN between the two cylinder heads...
Note: The reverse of the Flexible strip has 3-M adhesive that will stick to any cleaned surface...
And Then...
36-LED Front & Rear Motorcycle Wheel Kit
Yes install the 9-LED SingleColor WaterProof ShockProof Flexible Strip to the fork on the right side of your Front Wheel then install the 9-LED SingleColor WaterProof ShockProof Flexible Strip to the fork on the left side of your Front Wheel... Run the 6 feet of wire back to your battery area... Then install to the right/left rocker-arm shining into your Rear Wheel... Connect the two RED wire together and connect the two BLACK wires together...
It is that easy...
And Then...
54-LED Road Coverage Kit
Yes install the two 27-LED SingleColor WaterProof ShockProof Flexible Strip to the right and left side of the bottom frame point down to the hightway... This will shine down on the road and gives the effect that you are riding on a cloud of light...
Each strip has three feet of Tube Covered Heat Resistant Wire... Just Run the 3 feet of wire back to your battery area... Connect the two RED wires together and connect the two BLACK wires together...
Note: Install the strips to your frame with the use of the supplied 3-M adhesive and plastic wire ties...
It is real easy...
Now Connect the Engine Kit, Road Coverage Kit and the Front & Rear Wheel Kit to the E-Z connect Terminal:
Splice the RED (Positive) wires of the Engine Kit, Road Coverage Kit and the Front & Rear Wheel Kit together.
Splice the BLACK (Negative wires of the Engine Kit, Road Coverage Kit and the Front & Rear Wheel kit together.
Then connect the RED wire of the Lights to one wire of the On-Off Switch. Connect the othe wire of the On-Off Switch to one wire of the Fuse Holder. Connect the other RED wire of the Fuse Holder to the Positive Pole of the Battery.
Then connect the BLACK wire of the Lights to the Negative Pole of the Battery.
Activiate the On-Off Switch and you have the most beautiful Motorcycle Accent Lights you have ever seen...
This Kit Is Designed To Work On Any Bike Made...
7 Ultra Bright LED Colors Currently Available:
Blue (12,000 MCD)
Green (15,000MCD)
Red (10,000 MCD)
Yellow (7,000 MCD)
Purple (5,000 MCD)
White (20,000 MCD)
Orange (8,000MCD)
Please be advised that color PURPLE is a UV color and is almost half as bright as any other color...
Select your COLOR!!!
Yes an Engine Kit of 90-LEDs to accent the Engine area, then the Front & Rear Wheel Kit of 36-LEDs to highlight the chrome of both Wheels and then top it off with the Road Coverage Kit of 54-LEDs that will shine down on the road and gives the effect that you are riding on a cloud of light... A total of 180-LEDs in one kit... Nothing like it on the market...and it all is WaterProof and ShockProof...
This 180-LED Flexible Strip Kit has ultra-bright LEDs and for sure will please you... It's like a blast of light shining on your chrome... Like an eruption of light... An explosion of light... A detonation of light... I am sure you will get a bang out of it...
180-LED SingleColor WaterProof ShockProof Motorcycle Accent Light Kit
Remember: A lifetime guarantee. I don't give you any mumbo-jumbo just a very simple lifetime quarantee: should a light ever burn out or stop working for any reason, return it and I'll replace it. No ifs, ands or buts about it. You don't like my Kit just return it for a full refund of your purchase price including shipping cost. No questions asked... You don't get ripped with Joe-Florida!!!
It's Included!!!
3-M 94 Primer
PREPPED: "To prepare or prime"
Yes, 3-M 94 Primer is the best product on the market to prep the area where you are going to place the Flexible Strip. You will clean (degreaser) the location, you will rub the location with an included Alcohol Pad and one dry you will brush on the 3-M 94 Primer. Let dry for 3 to 5 minutes then secure the Flexible Strip to the location. Please understand that once you place the strip using these products and methods you will have to work at it to remove the strip. Be careful not to get 3-M 94 Primer on a noticiable finished painted or chromed surface. Best product to secure Flexible Strips in place.
Here's what you get:
2 Strips of 45-LEDs ea. for Engine Kit of Ultra High Brightness LEDs
4 Strips of 9-LEDs ea. for Front & Rear Wheel Kit of Ultra High Brightness LEDs
2 Strips 27-LEDs ea. for Road Coverage Kit of Ultra High Brightness LEDs
1 On/Off Switch
1 Fuse Holder w/ Two 3amp Fuses
1oz Tube of Silicone Sealant
10 4" Plastic Wire Ties
5 Butt Splices
10 Cradle Mounts
2 E-Z Connect Wire Terminals
4 Feet of Double 20 gauge Wire
New & Improved Supply Kit
1oz Tube of Silicone Sealant is included to seal any cut ends of Flexible Strips...
Detailed “Installation Instructions” are included but most important I am available via phone or e-mail if you need additional help... I don't go away after the sell...
Are the LED Bulbs Waterproof?
Just look at the picture below with the BLUE Strip in a vase of water...
Yes. If installed according to the instructions there is absolutely no way that water will affect the performance.
How long will these lights last??
Almost forever... well, 100,000+ hours of light time (that's over 11 years) and for a light bulb that's almost forever. Also, these lights generate no heat and draw about 3 mill amperes each.
"Quality LED Accent Light Products at a Fair Price"
Have a Blessed Day... Joe-Florida...
My no mumbo-jumbo life-time guarantee is good for as long as you own the bike. If a bulb burns out... You break one... Something doesn't work... whatever... I replace it free of charge...If you do not like my kit for any reason when you receive it just return the complete uninstalled kit within seven days of purchase and receive a full refund... No questions asked... And I will not abandon you after the sale... I am available to assist you with your installation just call or e-mail me.
Be Blessed... JoeFlorida..
Legal Information
|
Laws governing the use of custom lighting vary from state to state. Some of these lights or some of these colors may not be street-legal in some states, and are offered for off-road or show use only. Please check with your local authorities before purchasing.
|
This product was added to our catalog on Friday 16 September, 2011.
